European Journal of Wood and Wood Products
Издатель: Springer Nature · ISSN 0018-3768,1436-736X · 25 статей
-
Experimental and numerical study on size-dependent mechanical behavior of Mongolian Scots pine (Pinus sylvestris var. mongolica) specimens under axial compression
As a highly promising sustainable building material, wood has attracted considerable attention in structural engineering. However, the influence of specimen size on the compressive properties of wood specimens has not yet been...
-
A plugin for the parametric generation of cellular-scale wood geometric models for numerical analysis
Computer-aided engineering software is widely employed to investigate the relationships between macroscopic mechanical behavior and microstructural features of wood across multiple scales. Nonetheless, a significant challenge persists:...
-
Evaluation of thermally modified wood as a feedstock for briquette production
The share of modified wood in woodworking industry increases with thermal modification dominating the modified wood global production. Densification into briquettes or pellets is one of the ways to utilize a considerable amount of...
-
Flame-retarded, thermoplastic sheets for hot-pressing on poplar plywood: an alternative to thermoset laminates
As a building material, plywood products must fulfil several requirements such as aesthetic value, durability and good fire performance. To provide these attributes, high pressure laminates (HPL) are often used as top sheets, however,...
-
Lignin-based high-pressure laminates: effects of substitution level and hot-pressing time for high lignin formulations
The development of sustainable high-pressure laminates requires renewable alternatives to petrochemical phenol without compromising processing or performance. This work investigates hydroxy-methylated hardwood kraft lignin as a phenol...
-
Weather-induced colour change in wood: material response in different European locations
This study investigates the colour evolution of Norway spruce wood during one year of natural weathering across multiple European locations as part of a Round Robin experiment. Colour measurements ( CIE Lab ) were performed on samples...
-
Hydrothermal confinement and delignification assisted silicate stabilization enhance surface hardness and suppress set recovery in plantation grown Chinese fir
Surface densification can improve the surface performance of low density plantation wood, but moisture induced recovery of the compressed layer limits its dimensional stability. Here, localized surface hydration and asymmetric platen...
-
Finite element modeling of fatigue damage progression in unglued wooden mortise-tenon joints considering friction coefficient and fit degradation
This study first validated a proposed finite element model for analyzing the fatigue damage progression (FDP) in mortise-tenon (M-T) joints used in furniture frame construction. The required inputs, including the degradation of the...
-
Bio-based adhesives from distillers’ dried grains and soybean for wood composites:review on performance and sustainability
This review reports recent progress in the development of bio-based adhesives derived from agricultural byproducts, with emphasis on distillers’ dried grains (DDG) and soybean (SB) based systems for wood composite (WC) applications....
-
In situ polymerization of PEGDA/MMA network in sliced wood for high flexibility and thermally induced shape memory functionality
Sliced wood veneer maintains the natural texture and color of wood, but its lack of flexibility and difficulty in shaping limit its potential applications. In this study, a modified sliced wood veneer was successfully fabricated by...
-
Comparative analysis of charred wood layers produced by two distinct high‑temperature treatment methods
Developing innovative solutions for the thermal treatment of wood surfaces is a current research topic. In this regard, charring wooden boards represents a satisfactory compromise, providing adequate protection for the wood surface....
-
Investigating the effect of densification on heat release rate and total smoke release in cross-laminated timber: experimental and machine learning approaches
Timber, a popular construction material, has limited application due to its vulnerability to fire. Hence, the flammability behaviour of timber is continuously studied to enhance its fire resistance. This study introduces a...
-
The effect of specimen geometry on wood shrinkage and collapse in Eucalyptus grandis
Eucalyptus is the most widely planted hardwood genus globally and an important source of industrial roundwood. In many Eucalyptus species, a substantial proportion of shrinkage arises from cell collapse occurring above the fibre...
-
Time-dependent reversal of water-absorption performance in citric acid–xylitol–modified Scots pine across processing pathways
Citric acid (CA)–polyol systems offer promising formaldehyde-free wood modification, yet early liquid-water suppression does not guarantee long-term stability under prolonged wetting. This study evaluated the time-dependent...
-
Date palm wood-based foams with gellan gum binder for enhanced sound and thermal insulation in building applications
Biofoams are a promising alternative to fossil-fuel-derived materials for heat insulation in construction. However, the processing of biomaterials to produce bioaerogels involves multistep steps, making it costly and complicated. In...
-
Fatigue behavior of threaded rods bonded into glued-laminated timber for application in bridge construction
Due to the difficult climatic conditions and the fatigue stresses caused by traffic loads, timber is used comparatively little in bridge construction. Connections with bonded in rods (BiR) are of particular interest for structures with...
-
Optical and thermal characterization of thermochromic transparent wood as a potential smart glazing material
Transparent wood (TW) is an emerging bio-based glazing material, and the incorporation of thermochromic pigments offers a route toward glazing that modulates visible light in response to temperature. However, the effect of thermochromic...
-
Multi-scale mechanical and viscoelastic behaviour of major and lesser-used Congo Basin hardwoods: effects of radial position and moisture content
This study investigates the multi-scale mechanical and viscoelastic behaviour of nineteen Congo Basin hardwood species, including thirteen major commercial timbers and six lesser-used substitutes. A comprehensive approach was applied,...
-
Enhancing dyeing efficiency of bamboo culm through surface sanding: modifying microstructure and permeability for improved dyeing performance
Bamboo products are increasingly popular among consumers; however, their monotonous surface coloration and inherent natural defects limit their economic value. To address these issues, this study investigated the dyeing performance of...
-
Analysis of the strain characteristics of wood in three-point bending on the basis of the radial moisture content gradient distribution
Although the effects of average moisture content (MC) on wood mechanical properties are well documented, the quantitative influence of ubiquitous in-service internal moisture gradients on bending performance remains poorly understood....
-
Longitudinal variation in log properties of Pinus radiata in northern Tasmania: predicting log stiffness using resistance drilling
This study assessed within and between-stem variation in log dynamic modulus of elasticity (MOE) using 591, 2.5 m logs from 65 Pinus radiata D.Don trees. Trees were sampled across 13 plots (5 individuals per plot), across 7 stands from...
-
Potential of Korean Quercus variabilis virgin cork as an alternative cork resource: weathering, fungal, and termite resistance compared with European Quercus suber reproduction cork
Cork is a renewable material with potential for building applications, but information on Korean Quercus variabilis cork remains limited compared with commercial Quercus suber cork. This study compared the chemical composition,...
-
Bamboo particleboards bonded with lignin-modified vinyl acetate-ethylene adhesive: physical, mechanical, and thermal properties
The development of sustainable adhesive systems based on renewable resources is essential for advancing environmentally friendly lignocellulosic materials. However, limited information is available on the direct modification of vinyl...
-
Local contact behaviour of Norway spruce under compression parallel to fibres
Timber joints designed to transfer forces directly through timber-timber contact represent one possible approach to reducing the use of metal components in timber buildings. However, in tall timber buildings, joints are subjected to...
-
Rethinking engineered wood product manufacturing: opportunities for using partially seasoned timber feedstocks
The manufacture of engineered wood products (EWPs), such as glue laminated beams (glulam), has traditionally been reliant on using seasoned timber feedstocks. Reducing the timber’s moisture content (MC) before use provides many benefits...